3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 product description 3m? bumpon? protective products molded shapes - colored and clear series are pressure-sensitive. adhesive-backed polyurethane products. they can be used as feet, stops, spacers, and protectors in many applications. the urethane is a durable, resilient elastomer. the aggressive, high tack, pressure sensitive adhesive is protected with a release liner making application fast and easy. 3 technical data february 2012 top hat hemisphere cylindrical (flat top) top hat cylindrical (concave top) tapered square features all 3m? bumpon? protective products feature a plasticizer-free, urethane composition which exhibits: ? excellent skid resistance ? long aging resiliency ? will not crack or harden ? abrasion resistance ? resistance to marring and staining application ideas use almost anywhere slamming, scratching, nicking, scuffing, marring, sliding, vibration, or noise could be a problem for your product. ? feet on the bottom of small appliances, desk top or handheld electronic devices, electronic cabinetry, telephones, keyboards, foot pedals, scales, clocks, speakers, dispensers, and computers. ? stops for cabinet doors, lids, and drawers. ? spacers for picture frames to provide alignment; for electronic and automotive applications as an aid in assembly. ? protectors to prevent damage in shipping, and keep parts from direct contact with each other.
3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 (2) product number colors width inches (mm) height inches (mm) pad format cylindrical shapes (with flat tops) bumpon sj5012, sj5312*, sj5412** black, brown, white, gray, transparent*, true white** 0.50 (12.7) 0.14 (3.5) 5x8 (40) bumpon sj5744, sj5344* black, transparent* 0.75 (19.1) 0.16 (4.1) 4x10 (40) product number colors width inches (mm) height inches (mm) pad format cylindrical shapes (with concave tops) bumpon sj5001 black 0.50 (12.7) 0.14 (3.5) 5x8 (40) bumpon sj5009, sj5309* white, gray, brown, black transparent* 0.88 (22.3) 0.40 (10.1) 3x8 (24) product number colors width inches (mm) height inches (mm) pad format hemispherical shapes bumpon sj5302*, sj5402** transparent*, true white** 0.312 (7.9) 0.085 (2.2) 8x18 (144) [bumpon sj5402) 17x24 (408) [bumpon sj5302) bumpon sj5003* black, brown, gray, transparent* 0.44 (11.1) 0.20 (5.0) 8x7 (56) product number colors width inches (mm) height inches (mm) pad format bumpon sj5017, sj5317* white, gray, black, transparent* 0.75 (19.0) 0.38 (9.6) 4x10 (40) bumpon sj5027, sj5327* white, gray, brown, black, transparent* 0.63 (16.0) 0.31 (7.9) 5x8 (40) 3m bumpon protective products * bumpon sj5300 series identifies transparent products. ** bumpon sj5400 series identifies true white products. note: all dimensions ?.02 inches or ?.5 mm measured without the adhesive liner. important: some bumpon molded shapes listed (or specific color versions) may require special minimum order quantities. consult your local 3m representative or our website: www .3m.com/bumpons . bumpon sj5076, sj5376* black, transparent* 0.315 (8.0) 0.110 (2.8) 8x7 (56) bumpon sj5532 gray, black 1.88 (47.7) 0.66 (16.7) separate parts bumpon sj5306*, sj5406** transparent*, true white** 0.375 (9.5) 0.150 (3.8) 6x8 (48) bumpon sj5382* transparent* 0.25 (6.4) 0.075 (1.9) 8x18 (144) 12 44 76 01 09 32 02 03 06 17 27 82 molded shape number molded shape number molded shape number molded shape number
(3) 3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 product number colors width inches (mm) height inches (mm) pad format tapered square shapes bumpon sj5705, sj6105 black 1.275 (32.4) 0.250 (6.4) 3x3 (9) bumpon sj5007, sj5307* black, white, transparent* 0.413 (10.4) 0.98 (2.5) 6x9 (54) product number colors width inches (mm) height inches (mm) pad format bumpon sj5514 white, gray, black 0.81 (20.6) 0.52 (13.1) 4x1 (4) bumpon sj5018, sj5318* white, gray, brown, black, transparent* 0.50 (12.7) 0.23 (5.8) 8x10 (80) product number colors diameter of brim, inches (mm) height of brim, inches (mm) total height, inches (mm) form top hat and continuous strip shapes bumpon sj6115 - top hat black 0.625 (15.9) 0.093 (2.36) 0.187 (4.75) 5x8 (40) bumpon sj6125 - top hat black 0.625 (15.9) 0.093 (2.36) 0.250 (6.35) 5x8 (40) 3m bumpon protective products * bumpon sj5300 series identifies transparent products. note: all dimensions ?.02 inches or ?.5 mm measured without the adhesive liner. bumpon sj5008, sj5308* white, gray, black, transparent* 0.50 (12.7) 0.12 (3.1) 8x10 (80) bumpon sj5023, sj5323* white, gray, brown, black, transparent* 0.81 (20.5) 0.30 (7.6) 4x9 (36) bumpon sj5510 - continuous strip* white, gray, black, brown width, inches (mm): 0.50 (12.7) height, inches (mm): 0.15 (3.88) 50' rolls, 5 rolls per case 578 14 18 23 15 25 10 note: dimensions for bumpon sj6115 and bumpon sj6125 ?.005 inches (?.13 mm) for diameter ?.015 inches (?.38 mm) for height measur ed without adhesive liner. bumpon top hat products were created as an optional, non-skid foot shape, to be used in a recess (see page 7). they provide high resistance to removal, knock-off or shearing, when used in conjunction with a recessed location. * continuous molded strip can be cut by the customer to a specific length. the surface has lines that appear every 9" on the stri p. important: some bumpon molded shapes listed (or specific color versions) may require special minimum order quantities. consult your local 3m representative or our website: www .3m.com/bumpons . special products custom shape and color 3m can match most colors and customize shapes to your specifications. 3m has over 100 available standard and custom molded shap es. electronic format (cad and pdf) drawings are available on request. special easy strip packaging packaged into strips or die cut and perforated pads can help simplify some assembly operations. product currently available: ? 3m? bumpon? protective product sj5518 die cut perforated on pads of 64 ? 3m? bumpon? protective product sj5508 die cut and perforated on pads of 64 ? 3m? bumpon? protective product sj5523 4x1 matrix separated by perforations ? 3m? bumpon? protective product sj5514 4x1 matrix separated by perforations note: custom bumpon products may require a qualifying minimum quantity and/or a one time set-up charge. call your local 3m sales representative for more information. molded shape number molded shape number molded shape number
(4) 3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 typical physical properties and performance characteristics note: the following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3m bumpon protective products sj5000 sj5500 sj5300 3m test method sj5700 sj5400 sj6100 hardness, shore m astm-d2240 72 75 72 resilience, % astm-d2632, 30 5 30 0.125" sample kinetic coefficient of friction (mk) astm-d1894 (dependent on test surface) 1 stainless steel >1 >1 >1 glass >1 >1 >1 formica laminate 0.9-1.4 0.9-1.4 0.9-1.4 wood 0.9-1.4 0.9-1.4 0.9-1.4 abrasion resistance astm-c501 1.7-1.9 0.13 1.7-1.9 (taber h18, 1kg) g/1000 cycles 2 tensile, lbs/in 2 (mpa) 2 astm-d412, die a 600 (4.1) 740 (5.1) 600 (4.1) elongation,% 2 astm-d412, die a 100 65 100 dielectric strength, astm-d1000 200 370 200 volts/mil 2 stain resistance 3 3m-24 hours @ 158? no no no against white paint staining staining staining 7 days exposed to uv. flammability listing ul-94hb pass; pass; ul not ul ul recognized recognized recognized application temperature 40? (5?) to 125? (52?) service temperature constant: -30? (-34?) to 150? (66?) intermittent: up to 225? (107?) solvent and fuel resistance 3 24 hour immersion 5% detergent in water no apparent effect 25% ammonia in water no apparent effect bleach no apparent effect hydrochloric acid no apparent effect (1 normal solution) diesel fuel no apparent effect auto oil no apparent effect isopropyl alcohol slight swelling heptane slight swelling toluol considerable swelling lacquer thinner considerable swelling notes: 1 two important laws of friction applicable to bumpon products are: (1) friction is independent of the area of contact between so lids and (2) friction is proportional to the load between solid surfaces. thus, if the load (weight) is doubled the force required to cause sliding is also double. this is expressed mathematically as follows: sliding force = m k x weight. 2 these properties were run on sheet material from the same materials as the individual bumpon products 3 reference test for 24 hours. results may vary for different product application conditions.
(5) 3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 relative adhesive performance characteristics note: the following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3m bumpon protective products sj5000 sj5500 sj5300 sj5700 sj5400 sj6100 adhesive: natural rubber acrylic synthetic rubber r-30 a-20 r-25 initial adhesion low surface energy: good poor excellent high surface energy: good fair excellent adhesion (peel) low surface energy: good poor excellent high surface energy: good good excellent static shear 75? (25?): excellent excellent excellent 120? (49?): good excellent good 158? (70?) poor excellent fair dynamic shear: good excellent good solvent resistance: good excellent good adhesive performance note: the following technical information and data should be considered representative or typical only and should not be used for specification purposes. the following table on peel adhesion provide representative performance characteristics of the adhesive systems used in the construction of 3m? bumpon? protective products molded series products. 90 peel adhesion *peel force, oz. per 1/2 inch 3m bumpon protective products sj5000 sj5500 sj5300 sj5700 sj5400 sj6100 substrate: natural rubber acrylic synthetic rubber r-30 a-20 r-25 polypropylene 25 3 52 polystyrene 25 11 55 abs 25 25 55 stainless steel 22 25 55 aluminum 22 25 55 * 3m test method tm-2011; 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. testing completed using bumpon res ilient rollstock products sj5816, sj6016, and sj6216, which use the same adhesive system as the molded series products.
3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 (6) application techniques to obtain maximum adhesion, surfaces must be unified, dry, and free of contaminants. surface contact is essential to adhesive performance. to maximize contact on a substrate: ? clean surfaces with low strength solvent such as isopropyl alcohol (rubbing alcohol) or heptane. * ? apply firm pressure to help increase the cold flow and contact of the adhesive with the substrate. ? allow time (dwell) to increase the surface contact and adhesion (see illustrations below). *note: be sure to follow the manufacturer?s precautions and directions for use when using solvents. low adhesion high acrylic rubber 0 24 48 72 dwell time ? hours adhesive surface contact rubber adhesive vs. acrylic adhesive bond build-up environmental exposure colored and transparent 3m? bumpon? protective products are intended for interior applications where resilience and other physical properties will remain unchanged. when exposed to uv light for extended periods some slight discoloration or yellowing may occur. bumpon products may be used outdoors in a protected area with some discoloration possible; colored bumpon products may chalk. simultaneous exposure to high humidity and temperature may degrade (soften) the bumpon product urethane.
3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 (7) product selections considerations alignment alignment is more difficult with a rectangular shaped 3m bumpon protective product when no recess is provided. circular shaped product rectangular shaped product point of contact the point of contact provides either a large contact area or a very small (point) contact area depending on the shape of the bumpon product. flat hemisphere ? increased load capacity ? better wear resistance ? increased sound dampening ? increased energy absorption (side view) (side view) profile the profile is defined by the height and the diameter (or width) of the bumpon product. low profile high profile ? increased load capacity ? less susceptible to being sheared off substrate ? better hear dissipation ? not recommended if sideways shearing is possible recess a recess is not necessary; however, there are several benefits to providing a recess. ? provides target area for the bumpon product during attachment process ? improves adhesion performance: impact absorption and shear strength ? provides neater appearance ? provides uniform location (top view) (top view) storage store in original cartons at 60 to 80f (16 to 27c) and 40 to 50% relative humidity. shelf life to obtain best performance, use this product within 18 months from date of manufacture.
3m bumpon protective products molded shapes - colored and clear series sj5000 ? sj5300 ? sj5400 ? sj5500 ? sj5700 ? sj6100 (8) 3 3m and bumpon are trademarks of 3m company. formica is a registered trademark of the formica corporation. please recycle. printed in u.s.a. 3m 2012. all rights reserved. 60-5002-0526-9 3 electronics markets materials division 3m center, building 225-3s-06 st. paul, mn 55144-1000 1-800-251-8634 phone 651-778-4244 fax www.3m.com/bumpons for additional information to request additional product information or to arrange for sales assistance, call toll free 1-800-251-8634. address correspondence to: 3m, electronics markets materials division, 3m center, building 225-3s-06, st. paul, mn 55144- 1000. our fax number is 651-778-4244 or 1-877-369-2923. in canada, phone: 1-800-364-3577. in puerto rico, phone: 1-787-750-3000. in mexico, phone: 52-70-04-00. important notice all statements, technical information, and recommendations related to 3m?s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3m?s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture at the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3m?s option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. certification/recognition msds: refer to product label and material safety data sheet for health and safety information before using this product. tsca: this product is defined as an article under the toxic substances control act and therefore, it is exempt from inventory listing requirements. rohs: this product complies with the requirements of eu directive 2002/95/ec and 2005/618/ec.
|
